Precise area and linscan cameras syncronisation across different frame grabbers Glitch removal filter available on all System I/O input linesįor DIN and TTLIO lines: 50 ns, 100 ns, 200 ns, 500 ns,1 µsįor IIN lines: 500 ns, 1 µs, 2 µs, 5 µs, 10 µsĨ quadrature encoders with A/B and Z inputsĮach I/O line can generate event on configurable edge Isolated lines – opto isolated lines with voltage range up to 30V The application software can be notified of the occurrence of various events:Īny System I/O input lines can be connected to any I/O lineĪny I/O line can be used to decode A/B and Z signals of a motion encoderĪny I/O line can generate any trigger event Unpacking of 10-/12-/14-bit to 16-bit with justification to LSb Bilinear 3×2 for linescan with gradient correctionįull 16bit resolution 18bit coefficiens table.Support for quadrature motion encoders, with programmable filters, selection of acquisition direction and backward motion compensation. Support of infinite acquisition, without missing lines. Support of external hardware trigger, with optional delay and filtering. Precise control of start-of-scan and end-of-scan triggers. Support of external hardware trigger, with optional delay, filtering and trigger decimation.Īccurate control of the strobe position for strobe light sources. Support of triggering from encoder or timer Support of camera exposure/readout overlap. Precise control of asynchronous reset cameras, with exposure control. BayerXX8, BayerXX10, BayerXX12, BayerXX14, BayerXX16 where XX = GR, RG, GB, or BG.Raw, Monochrome, Bayer, RGB, YUV, YCbCr and RGBA (PFNC names): – Gray-scale and color (RGB and Bayer CFA) – A +12V power source must be connected to the auxilary power input connector PoCXP Device detection and automatic power-on.– 19 W of 24V DC regulated power per CoaXPress connector Maximum aggregated camera data transfer rate 16.8 W (3.8 W +3.3V, 13 W +12V), excluding camera and I/O power outputĬoaXPress v2.1 (CoaXPress 1.1 backward compatible)ġ CoaXPress Host connection status per connector Phisical address support (GPU transfers)Ħ,710 MB/s (Host PC motherboard dependent).6.25 GT/s (PCIe 2.0) with reduced performance.HD DB26 D-sub panel mount (26-pin 3-row, through hole, right angle)Ħ-pin PEG power socket 12 VDC power input for PoCXP camera(s) Standard profile, half length, 8-lane PCI Express cardįor insertion in a standard height, 8-lane or higher, PCI Express card slotġx External I/O connector on front bracket panel Komodo II CoaXPress Frame Grabber with 4 channels The Frame Grabber utilizes PCIe Gen3 x8 lanes for communication with Host PC for video uploading and configuration. The Komodo II uses standard Micro-BNC connectors as a CoaXPress interface to the camera and a standard HD DB26 D-sub panel mount connector for general-purpose I/O. This product also provides GPIO for machine control signals, such as triggers, shaft encoders, exposure control, and general I/O, which can be controlled aside from video stream acquisition. The Komodo II can easily receive video streams on the CoaXPress 12G links and transmit them to computer memory through the PCIe interface. Each link supports standard CoaXPress bitrates up to 12.5 Gbps including 13W PoCXP. This CoaXPress 12G Frame Grabber is ideally suited for industrial, defense and aerospace Machine Vision Systems and applications. It is used for simultaneous capture from up to four single link cameras. The Komodo II can receive video streams from up to 4 CoaXPress links in single, dual, or quad modes. Komodo II is best in class Frame Grabber supporting CoaXPress 12G standard and is certified by the Japan Industrial Imaging Association (JIIA).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |